Intellinet Network Solutions 524940

• Description: The device comes with the Wireless-N capability that can stream data up to 150Mbps. It also comes with an available USB port for 3G connection. The device also comes with 4-LAN ports with AUTO-MDIX features which provide additional network connection options. The device can also secure communication and data transfer for small businesses through VPN passthrough.
• Brand: Intellinet Network Solutions
• Release Date: 03/2011
• Default Gateway IP: 192.168.2.1
• Default Username: admin
• Default Password: 1234

Follow our site to get more tip and direction 192.168 1.1

Common router IP address 192.168.1.254

192.168.1.254 IP address is the default private IP address for some home broadband routers and broadband modems such as 2Wire, Aztech, Billion, Gigabyte, Motorola, Netopia, SparkLAN, Thomson and Westell modems for CenturyLink.

While the router itself has the private IP of 192.168.1.254, it assigns any devices in its network a different, private IP address. All IP addresses on a network should have a unique address (within that network) to avoid IP address conflicts.

Other common private IP addresses used by modems and routers are 192.168.1.100 and 192.168.1.101.

The Router's Control Panel

A router's default gateway IP address is set by the manufacturer at the factory, but you can change it at any time using its control panel. Entering 'http://192.168.1.254' (or simply click 192.168.1.254) into a web browser's address bar enables access to your router's control panel. Here you can change the router's IP as well as configure several other options, depending on your router.

Once you have access to your router's control panel, you can configure the router in several ways. First off, be sure to set a secure username/password combination. Without that, anyone can access your router's panel and change its settings without your knowledge.

Routers usually allow users to change other settings, including the IP addresses it has assigned to devices on the network.
Follow our website to get more tip and direction 192.168 1.1

How to Change Your Wi-Fi Password

Have you ever been worried about your personal information being exploited because your Wi-Fi isn't secure enough? Keeping your router password protected and changing the password regularly are essential keys to protecting your network and your data.

Your Wi-Fi router comes with a default network name and password, and both are often printed on the router itself. But you can change the name and password to anything you want in just a few clicks.

Changing your default network name gives you a chance to use something more personalized than “NETGEAR-DualBand-N” or “Linksys” or “TP-LINK_8B1E44”. You could also use a password that’s easier to remember.

1. Open your router's configuration page & enter your router's username and password

Standard router addresses are 192.168.1.1, 192.168.0.1, 192.168.2.1, or 10.0.1.1 (Apple) or 10.0.0.1 (Xfinity). Enter the address into your browser's address bar.

If none of the above addresses grant you access to the configuration page, follow this guide to find out your router's address: How To Find Your Router IP Address.

If all else fails, you have to reset your router (Recover Router Password). Then, look up the default address for that router model and enter it into your browser.

Some routers come with configuration software. If you've previously installed your configuration software, you can use that instead of the web browser interface.

2. Open the Wireless section

Note: If your "Wireless Settings" section has multiple subsections, open the Wireless Security or Security page.

3. Change the name (SSID) and/or password

Look for the box labeled "Password", "Passphrase" or "Shared Key". You can enter your new password into this box. Some routers will ask that you type the password again to ensure that you entered it correctly.

Tips:

• Try to create a strong password that would be difficult if not impossible to guess. It should not be related to anything personal, and should include a liberal amount of numbers, random cases, and special characters such as "!", "$" and "#".
• A strong password is usually at least 8 characters long.

Check out your security type:

• There are three main types of wireless encryption: WEP, WPA, and WPA2. For the most secure network, you should be using WPA2. You may run into issues connecting older devices, however, in which case you could switch to WPA or WPA/WPA2.
• Selecting WEP is NOT recommended, as WEP encryption is very easy to break (it can take less than 30 minutes to crack a WEP password).

4. Save your settings

Once you are done entering your new password, click the Apply or Save button. The button's location is different for every router but is typically located at the top or bottom of the page. The router will take a few moments to process the change, at which point any devices currently connected would be disconnected. After your settings are changed, you can connect to your wireless network using your new password.

Follow our site to get more tips and guides about 192.168 1.1

How To Setup A Home Network Router

This step-by-step guide explains how to set up a broadband router for home computer networks. The exact names of configuration settings on these routers vary depending on the specific model. However, this same general process applies.

Choose a suitable location

Choose a good location to begin installing your router such as an open floor space or table. This does not need to be the permanent location of the device: Wireless routers sometimes need careful positioning and deployment in places difficult to reach.

At the beginning, it's better to choose a location where it's easiest to work with the router and worry about final placement later.

Turn It On

Plug in the router's electrical power source then turns on the router by pushing the power button.

Connect your Internet Modem to the Router (optional)

Older network modems connect via an Ethernet cable but USB connections have become increasingly common. The cable plugs into the router jack named WAN or uplink or Internet. When connecting devices with network cables, be sure each end of the cable connects tightly: Loose cables are one of the most common sources of network setup problems. After connecting the cable, be sure to power cycle (turn off and turn back on) the modem to ensure the router recognizes it.

Connect One Computer to the Router

Connect this first computer to the router via a network cable. Note that Using the Wi-Fi connection of a wireless router for initial installation is not recommended as its Wi-Fi settings are not yet configured: Temporarily using a cable for router installation avoids unstable or dropped connections.

(After router installation is complete, the computer can be changed over to a wireless connection as needed.)

Open the Router's Administration Panel

From the computer connected to the router, first, open a Web browser. Then enter the router's address for network administration in the Web address field and hit return to reach the router's home page.

Many routers are reached by either the Web address "http://192.168.1.1" or "http://192.168.0.1". Find out your router's default IP, username, and password at our default router passwords, or consult your router's documentation to determine the exact address for your model. Note that you do not need a working Internet connection for this step.

Log in to the router

The router's home page will prompt for a username and password. Both are provided in the router's documentation. You should change the router's password for security reasons, but do this after the installation is complete to avoid unnecessary complications during initial setup.

Enter Internet Connection Information

If you want your router to connect to the Internet, enter Internet connection information into that section of the router's configuration (exact location varies). For example, those using DSL Internet often require entering PPPoE username and password settings into the router... Likewise, if you requested and have been issued a static IP address by your Internet, the static IP settings (including network mask and gateway address) supplied by the provider must be set in the router.

Update the MAC Address of the Router

Some Internet providers authenticate their customers by MAC address. If you were using an older network router or another gateway device to connect to the Internet before, your provider may be tracking that MAC address and prevent you from going online with the new router.

If your Internet service has this restriction, you can (through the administrator console) update the MAC address of the router with the MAC address of the device you were using previously to avoid having to wait for the provider to update their records. Read How to Change a MAC Address for a detailed description of this process.

Consider changing the network name (often called SSID)

Routers come from the manufacturer with a default name chosen, but there are advantages to using a different name instead. Read How to Change the Router SSID for detailed instructions.

Verify the Local Network Connection

Verify the local network connection between your one computer and the router is working.

To do this, check that the computer has received valid IP address information from the router.

Verify Your Computer Can Connect to the Internet Properly

Open a Web browser and visit a few Internet sites such as http://wireless.about.com/.

Connect Additional Computers to the Router

When connecting from a wireless device, ensure the network name (SSID) chosen matches that of the router.

Configure Network Security Features

Configure additional network security features as needed to guard your systems against Internet attackers. Check out this guide for detailed instructions: How To Change Wi-Fi Password and SSID.

Finally, place the router in an optimal location and it's time to have a beer :-).
Follow our site to get more tips and guides about 192.168 1.1